New hosting provider, site re-built from scratch, clutter removed, new layout (resembling the pre-2021 design). Added user comment function.
-
Advanced configuration
Once the control panel has been switched to advanced mode, things begin to look a little more complicated. The device list is now expandable and you can enable more than one item at a time. The device list contains Devices, Device Interfaces and so called “Pins”. Devices are independent hardware units most of the time.…
-
Device aggregation
Using the button next to each entry, you can now selectively enable/disable each particular item in the device list. This way, you can also create multi-device-setups (“aggregate devices”). Multi-device-setups require that all the devices involved are running from the same clock source. You can achieve this by daisy-chaining devices via S/PDIF etc. On-board devices usually…
-
Latency Compensation
Since ASIO4ALL does not have sufficient knowledge of the underlying hardware/driver architecture, it can only guess the actual latencies involved. With these sliders you can compensate for the latencies unknown to ASIO4ALL such that recordings in your sequencer Software are properly aligned with the rest. Note: In multi-device-setups the largest respective value of all devices…
Comments
56 responses to “Site re-launch”
Пожалуйста сделайте что нибудь версия 2.15 не дает нормально работать с Давинчи резолв 18. Прога просто постоянно крашится, а в статус баре Значек асио4алл с восклицательным знаком.
Thanks for making this program available.
Unfortunately, it does not work on my new Windows 11 PC using Sound Forge version 10.
Sound forge can see the ASIO drivers but does not work with them correctly. I play a song in Sound Forge and it plays through the headphones, I stop and restart playback and it comes out the speakers, if I do it a third time I get en error message saying the driver is not installed. Then I have to reboot the PC to start again.
The version of Sound Forge is from the Windows XP era. So, it’s surprising it runs at all. But, It used to work with an M-Audio supplied ASIO driver, so I thought I would give it a try.
Thanks anyway.
The software download is here: https://asio4all.org/2-15/
For those who only seem to be getting as far as the desktop shortcut to the website, ASIO4ALL will not appear until it is running. Open your DAW and select ASIO4ALL as your output device. A green icon will then appear in the lower right notification area of the taskbar. Click it to adjust settings, including the output you want to use.
If you’re using Reaper and have ‘close device when not in use’ enabled, the icon will disappear when you try to click it (doh!). Just go back to Reaper and hit ‘play’, and then you can access ASIO4ALL’s settings. You don’t need to open a project to do this.
Hope this helps!
Hey all. I would to get help downloading asio4all.
Don’t bother, the owner/developer decided to become a major asshole and design this piece of crap to scare you away from downloading his precious little tool.
gratuito ma con carta di credito????? e cosa è questa novità?
Hello lovely man and world, thank you for asio4all, “You Are” doing what ms should be doing in the 1st place, may your dreams be full of unicorns and shooting stars for all your days and nights. ripley signing off.
Hello lovely man and world, thank you for asio4all, tour doing what ms should be doing in the 1st place, may your dreams be full of unicorns and shooting stars for all your days and nights. ripley signing off.
There are no tutorials up for how to install this now. All I can see everywhere is “Dri8ver Support One” I didn’t need all this stuff last time I had Asio4All working fine with my set up. I simply want it to use Helix Native vst plug in for Reaper DAW but I am having problems just getting it installed which i do not understand because I had it on my computer for Rocksmith before now its just gone and i cant get it back
What’s wrong with navigating “Overview->Download”?
CLICK ON WHAT, YOU DOLT!? THIS WEBSITE IS JUST ADS
What’s wrong with “Hello, please, if you have time, thank you”????
I could bet that the ASIO4ALL guys don’t owe you anything.
Good luck. I appreciate the work you put in but the website is a mess! Covered in spam download links unfortunately so easy to click on the wrong one…
Why am I unable to use outputs 3 and 4 on my Tascam 4X4 interface through ASIO4ALL?
Are you able to use all 4 outputs for normal Windows sounds? If yes, we need to look into that.