ASIO4ALL Official Home

Universal Windows ASIO Driver

Version 2.11 Released!

  • Combined 32/64 bit version, supports Win 98SE/ME/2k/XP/MCE/2003/XP64 and Vista/Windows 7/Windows 8.x x86/x64
  • After more than 4 years, of course, this is a *major* update!           

Changes since version 2.10:

  • Improvement: Make an attempt to reclaim an unavailable audio device, includes workaround for a (confirmed) Windows bug.
  • Improvement: Add general fixed factor resampling capabilty.
  • Improvement: Latencies now displayed for the preferred buffer size, if host elects to violate the spec.
  • Improvement: Support for single common sample rate that is *not* a multiple of 8 or 11.025.
  • Workaround: Realtek PULL mode not supported for “odd” ASIO buffer sizes. Symptom was a “Beyond Logic” error depending on. ASIO buffer size.
  • Fix: Potential application compatibilty issue regarding ASIO reset request message.
  • Fix: Increased latency in x64 mode.
  • Fix: Pull mode _and_ latency display now working.
  • Fix: ASR issue with MSVC 2013 x64 -> Performance impact with hosts compiled with MSVC 2013.
  • Fix: UI appearance with different system locale.
  • Fix: Hang with some x64 hosts.
  • Fix: Crash on exit of A4Apanel64.exe.
  • Fix: Minor memory leak.
  • Fix: All known 2.11 Beta(1,2) regressions fixed.
ASIO4ALL 2.11 Downloads ⮱

Posted

in

,

by

Michael Tippach

Tags:

Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

Copyright © Michael Tippach

Imprint | Privacy

Powered by WordPress

ASIO is a trademark of Steinberg Media Technologies GmbH.  All other trademarks are the property of their respective owners, used for product identification purposes only.

  • Advanced configuration

    Advanced configuration

    Once the control panel has been switched to advanced mode, things begin to look a little more complicated. The device list is now expandable and you can enable more than one item at a time. The device list contains Devices, Device Interfaces and so called “Pins”. Devices are independent hardware units most of the time.…

    more

  • Device aggregation

    Device aggregation

    Using the button next to each entry, you can now selectively enable/disable each particular item in the device list. This way, you can also create multi-device-setups (“aggregate devices”). Multi-device-setups require that all the devices involved are running from the same clock source. You can achieve this by daisy-chaining devices via S/PDIF etc. On-board devices usually…

    more

  • Latency Compensation

    Latency Compensation

    Since ASIO4ALL does not have sufficient knowledge of the underlying hardware/driver architecture, it can only guess the actual latencies involved. With these sliders you can compensate for the latencies unknown to ASIO4ALL such that recordings in your sequencer Software are properly aligned with the rest. Note: In multi-device-setups the largest respective value of all devices…

    more

  • Hardware Buffer on/off

    Hardware Buffer on/off

    Note: For WaveRT drivers, this box is labeled “Allow Pull Mode (WaveRT)” instead! Enables the hardware buffer for the highlighted device. This only works for so called “WavePCI” miniports, as other types of WDM drivers do not usually allow direct access to the hardware buffer. Adjustment for best hardware buffer performance involves the “ASIO Buffer…

    more

  • Kernel Buffers/Buffer Offset

    Kernel Buffers/Buffer Offset

    If hardware buffering is disabled, this control lets you add up to two more buffers to be queued for audio output. Each additional buffer increases the output latency of the device by the time it takes to play one buffer. Therefore, the initial setting of “2” should only be changed on less powerful machines, where…

    more